MANAV RACHNA INTERNATIONAL INSTITUTE OF RESEARCH AND STUDIES
(Formerly MANAV RACHNA INTERNATIONAL UNIVERSITY )
Deemed to be University under section 3 of the UGC Act,1956
LAB EQUIPMENTS- DEPARTMENT OF MECHANICAL ENGINEERING
| MANAV RACHNA INTERNATIONAL INSTITUTE OF RESEARCH AND SCIENCE | ||
| FACULTY OF ENGINEERING & TECHNOLOGY | ||
| DEPARTMENT OF MECHANICAL ENGINEERING | ||
| DETAILS OF LAB FACILITIES | ||
| Sr. No. | Name of the Lab | Name of Equipment/Trainer with brief specifications |
| 1 | FM&T | Pelton Wheel Turbine Test Rig |
| 2 | Francis Turbine Test Rig | |
| 3 | Gear Oil Pump Test Rig | |
| 4 | Kaplan Turbine | |
| 1 | HEAT TRANSFER LAB | Thermal Conductivity of Metal bar |
| 2 | Heat Transfer in Natural Convection | |
| 3 | Heat Transfer through lagged pipe | |
| 4 | Thermal conductivity of insulating slab | |
| 5 | Cross flow heat exchanger | |
| 6 | Heat Transfer in Forced Convection | |
| 7 | Heat Transfer in PIN FIN | |
| 8 | Emmissivity Measurement Apparatus | |
| 9 | Parallel Flow / Counter Flow Heat Exchanger | |
| 10 | Stefan Boltzman Apparatus | |
| 11 | Two phase heat transfer apparatus | |
| 1 | THERMAL LAB | Dead Weight Tester |
| 2 | Lan Cashire Boiler Model | |
| 3 | Bob Cock and Wilcox Boiler Model | |
| 4 | Lever safety Valve Model | |
| 5 | Spring loaded safety valve model | |
| 6 | Feed check valve model | |
| 7 | Steam Injector Model | |
| 8 | Stop valve | |
| 9 | Steam Engine Model | |
| 10 | Stuffing Box Model | |
| 11 | Cochran Boiler Model | |
| 12 | Locomotive Boiler Model | |
| 13 | Delaval Turbine Model | |
| 14 | Reaction Turbine Model | |
| 15 | Cooling Tower Model | |
| 16 | Air or Steam Pressure Turbine Model | |
| 17 | Two stroke petrol engine test rig | |
| 18 | Air compressor of two stage – two cylinder test rig | |
| 19 | De-level Turbine Transparent Window Model | |
| 20 | Pressure and Velocity Compounded Turbine Model | |
| 21 | Pure Reaction Turbine Model | |
| 22 | Surface Condenser Model | |
| 23 | Jet Condenser Model(Parallel Type) | |
| 24 | Jet Condenser Model(counter flow model) | |
| 25 | Evaporative Condenser Model | |
| 26 | Air Pre-heater Model | |
| 27 | Sectional model of 2-stroke petrol engine | |
| 28 | Sectional model of 4-stroke petrol engine | |
| 29 | Sectional model of 2-stroke diesel engine | |
| 30 | Sectional model of 4-stroke diesel engine | |
| 31 | Gas Turbine Model | |
| 32 | High steam and low water steam valve model | |
| 33 | Green Economiser Model | |
| 34 | Sudgen Super Heater Model | |
| 35 | 1 cylinder 4-stroke petrol engine test rig | |
| 36 | 4 cylinder 4-stroke petrol engine with hydrolic break dynometer | |
| 1 | FLUID MECHANICS LAB | Impact of jet on vanes |
| 2 | Discharge over notch | |
| 3 | Losses due to friction in pipeline | |
| 4 | Flow through orifice and mouthpiece | |
| 5 | Bernoulli’s Theorem Apparatus | |
| 6 | Reynolds apparatus | |
| 7 | Discharge through venturimeter &orifice meter rota meter | |
| 8 | Loses due to pipe fitting sudden enlargement and contraction | |
| 1 | Refrigeration & Air-conditioning Lab | Refrigeration Test Rig Capacity 1/3 Ton |
| 2 | Air-conditioning Test Rig Capacity 1.5 Ton | |
| 3 | Mechanical Heat Pump Capacity 1/3 TR (P253) | |
| 4 | ICE Plant Tutor Circuit Capacity 20 kg/day | |
| 1 | DYNAMICS OF MACHINE | Cam Analysis apparatus |
| 2 | Motorised Gyroscope Test Rig | |
| 3 | Governor Apparatus | |
| 4 | Static and Dynamic Balancing Machine | |
| 5 | Universal vibration apparatus | |
| 6 | Motorized Gyroscope Apparatus | |
| 7 | Universal Governor Apparatus | |
| 8 | Whirling of shaft apparatus | |
| 9 | Static and Dynamic Balancing Machine | |
| 10 | Compound gear train | |
| 11 | Epicyclic gear train Apparatus | |
| 12 | Grashoff’s law Apparatus | |
| 13 | Coriollis component Apparatus | |
| 1 | MATERIAL SCIENCE LAB | Inclined Metallurgical Microscope(two) |
| 2 | Material of Different Structure | |
| 3 | Heat Treatment Furnace | |
| 4 | Metallurgical Polishing Machine | |
| 1 | SOM LAB | Universal Testing Machine |
| 2 | Extensometer with Two Dial Gauge | |
| 3 | Impact Testing Machine HIT-30 | |
| 4 | Spring Testing Machine ETC | |
| 5 | Hardness Testing Machine | |
| 6 | Beam Testing Machine | |
| 7 | Shear Force Apparatus | |
| 8 | Dimond Indentor | |
| 9 | Vicker hardness tester | |
| 10 | Torsion testing machine | |
| 11 | Fatigue testing machine | |
| 1 | Applied Mechanics Lab | Bell crank lever apparatus |
| 2 | Combined inclined plane friction slide apparatus with iron base (transfer from BM lab) | |
| 3 | Combined inclined planes friction slide apparatus with wooden base | |
| 4 | Moment of inertia of flywheel (25cm) | |
| 5 | Winch crab double purchase | |
| 6 | Worm and worm wheel single start | |
| 7 | Worm and worm wheel double start | |
| 8 | Worm and worm wheel triple start | |
| 9 | Screw jack simple | |
| 10 | Parallel force apparatus | |
| 11 | Parallelogram force apparatus | |
| 12 | Lami’s theorem apparatus | |
| 13 | Varignon’s theorem | |
| 14 | pulley apparatus | |
| 15 | circular disc apparatus | |
| 16 | simply supported roof , truss apparatus | |
| 1 | Kinematics of Machine Lab | Dog clutch drive (Single Sided) |
| 2 | Cone clutch Model | |
| 3 | Flanged coupling | |
| 4 | Oldham coupling Model (Rolling Friction) | |
| 5 | Allen Link Motion Model | |
| 6 | Differential gear model | |
| 7 | Helical gear model | |
| 8 | Combined Inclined Plane models | |
| 9 | Pulley Demonstration Set Model | |
| 10 | Wheel and Differential Axle | |
| 11 | Crank & Slotted Link Drive | |
| 12 | Slider Crank Mechanism | |
| 13 | Cam with straight line follower Model | |
| 14 | Face- Cam drive free follower Model | |
| 15 | Belt Drive Toothed Model | |
| 16 | Belt Drive Two Stage Model | |
| 17 | Belt Drive Model | |
| 18 | Hook’s Coupling Single | |
| 19 | Hook’s Coupling Doble | |
| 1 | CIM LAB | Deep Drawing Machine |
| 2 | CNC Lathe Trainer | |
| 3 | CNC Milling Trainer | |
| 1 | Metrology/Mechatronics Lab | Profile Projector |
| 2 | Floating Carriage | |
| 3 | Surface Roughness measuring Machine | |
| 4 | Surface Plate | |
| 5 | PLC Trainer with modules, Scientific dual power Supply | |
| 6 | Auto Collimeter | |
| 7 | Tool maker microscope | |
| 8 | Gear roller tester (parkinson type) | |
| 9 | Floating Carriage micrometer | |
| 1 | Simulation Lab | MATLAB |
| 2 | Simulink | |
| 3 | Symbolic math toolbox | |
| 4 | DSP System tool box | |
| 5 | Comunication system toolbox | |
| 6 | Image processing toolbox | |
| 7 | Fuzzy logic toolbox | |
| 8 | Neural network toolbox | |
| 9 | Control system toolbox | |
| 10 | optimization toolbox | |
| 11 | Global optimization toolbox | |
| 12 | Robust controle toolbox | |
| 13 | Aerospace toolbox | |
| 14 | Antenna toolbox | |
| 1 | Workshop | Lathes |
| 2 | Milling m/c | |
| 3 | Shapers | |
| 4 | Drilling m/c | |
| 5 | Power hacksaw | |
| 6 | Surface grinder | |
| 7 | Slotter | |
| 8 | Wood turning lathe | |
| 9 | Wood planar | |
| 10 | Electric Arc Welding sets and booths | |
| 11 | MIG welding machine | |
| 12 | TIG Welding machine | |
| 14 | Radial drill machine | |
| 15 | PRECISION LATHE MACHINE | |
| 16 | MIG WELDING MACHINE | |
| 17 | High speed precision lathe | |
